How to 100% pass 200-125 exam? Lead2pass provides the guaranteed 200-125 exam dumps to boost up your confidence in 200-125 exam. Successful candidates have provided their reviews about our 200-125 dumps. Now Lead2pass supplying the new version of 200-125 VCE and PDF dumps. We ensure our 200-125 exam questions are the most complete and authoritative compared with others’, which will ensure your 200-125 exam pass.
Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/200-125.html
The access control list shown in the graphic has been applied to the Ethernet interface of router R1 using the ip access-group 101 in command.
Which of the following Telnet sessions will be blocked by this ACL? (Choose two.)
A. from host A to host 22.214.171.124
B. from host A to host 126.96.36.199
C. from host B to host 188.8.131.52
D. from host B to host 184.108.40.206
E. from host C to host 220.127.116.11
F. from host F to host 18.104.22.168
The following access list below was applied outbound on the E0 interface connected to the 22.214.171.124/29 LAN: access-list 135 deny tcp 126.96.36.199 0.0.0.7 eq 20 any access-list 135 deny tcp 188.8.131.52 0.0.0.7 eq 21 any How will the above access lists affect traffic?
A. FTP traffic from 184.108.40.206 will be denied
B. No traffic, except for FTP traffic will be allowed to exit E0
C. FTP traffic from 220.127.116.11 to any host will be denied
D. All traffic exiting E0 will be denied
E. All FTP traffic to network 18.104.22.168/29 will be denied
The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.0 0.0.0.255 any. What is the effect of this access list configuration?
A. ermit all packets matching the first three octets of the source address to all destinations
B. permit all packet matching the last octet of the destination address and accept all source addresses
C. permit all packet matching the host bits in the source address to all destinations
D. permit all packet from the third subnet of the network address to all destinations
A default Frame Relay WAN is classified as what type of physical network?
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint
Which of the following are key characteristics of PPP? (Choose three.)
A. can be used over analog circuits
B. maps Layer 2 to Layer 3 address
C. encapsulates several routed protocols
D. supports IP only
E. provides error correction
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?
A. Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the
B. Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic
C. Configure many sub-interfaces on the same subnet
D. Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
The Frame Relay network in the diagram is not functioning properly.
What is the cause of the problem?
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
As a CCNA candidate, you must have a firm understanding of the IPv6 address structure. Refer to IPv6 address, could you tell me how many bits are included in each filed?
Refer to the exhibit. How many broadcast domains exist in the exhibited topology?
Refer to the exhibit. The network administrator has created a new VLAN on Switch1 and added host C and host D. The administrator has properly configured switch interfaces FastEthernet0/13 through FastEthernet0/14 to be members of the new VLAN. However, after the network administrator completed the configuration, host A could communicate with host B, but host A could not communicate with host C or host D. Which commands are required to resolve this problem?
A. Router(config)# interface fastethernet 0/1.3
Router(config-if)# encapsulation dot1q 3
Router(config-if)# ip address 192.168.3.1 255.255.255.0
B. Router(config)# router rip
Router(config-router)# network 192.168.1.0
Router(config-router)# network 192.168.2.0
C. Switch1# vlan database
Switch1(vlan)# vtp v2-mode
Switch1(vlan)# vtp domain cisco
Switch1(vlan)# vtp server
D. Switch1(config)# interface fastethernet 0/1
Switch1(config-if)# switchport mode trunk
Switch1(config-if)# switchport trunk encapsulation isl
More free Lead2pass 200-125 exam new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDM0s1aXlFTXBWdGM
The Cisco 200-125 exam questions from Lead2pass are the most reliable 200-125 study guide for Cisco exam. We offer the latest 200-125 PDF and VCE dumps with new version VCE player for free download, and the newest 200-125 dump ensures your exam 100% pass. A large number of successful candidates have shown a lot of faith in our 200-125 exam dumps. If you want pass the Cisco 200-125 exam, please choose Lead2pass.
2017 Cisco 200-125 (All 929 Q&As) exam dumps (PDF&VCE) from Lead2pass:
https://www.lead2pass.com/200-125.html [100% Exam Pass Guaranteed]