[Full Version] Free Version Lead2pass Cisco 200-601 PDF Dumps With Exam Questions Download (41-50)

2016 December Cisco Official New Released 200-601 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

There are many companies that provide 200-601 braindumps but those are not accurate and latest ones. Preparation with Lead2pass 200-601 new questions is a best way to pass this certification exam in easy way.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-601.html

QUESTION 41
Which characteristic causes multimode fiber-optic cable to differ from single mode?

A.    by allowing multiple network services in the same cable
B.    shorter maximum network segment length for a given bandwidth
C.    a wider variety of available connector types
D.    use outdoors as well as indoors

Answer: B

QUESTION 42
Which command globally enables QoS on a Cisco Industrial Ethernet switch?

A.    switch(config)#qos enable
B.    switch(config)#mls queuing enable
C.    switch#enable queuing
D.    switch(config)#mls qos

Answer: D

QUESTION 43
You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the switch?

A.    While online in RSLogix 5000 software the changes made in the AOP are pushed to the switch after pressing the Set button.
B.    All of the changes are automatically pushed to the switch.
C.    Changes to the AOP can only be made from the switch, not in RSLogix 5000.
D.    RSLogix 5000 will push the changes in the AOP to the Stratix 5700 when you right click on the switch, and choose download to switch

Answer: A

QUESTION 44
Refer to the exhibit. SW1, SW2 and virtual switch are connected in a loop. SW1 and SW2 are standard layer-2 switches.
Which loop prevention mechanism is best suited for use within this topology?

A.    Per-VLAN Rapid Spanning Tree Protocol+
B.    End-Host Mode
C.    Multi-chassis EtherChannel
D.    BPDU Guard

Answer: B

QUESTION 45
Refer to the exhibit. NAT has been configured on the router ‘GW’ and the IP addresses of router ‘GW’ have been configured properly. Users of PC1 and PC2 are able to ping the IP address
198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem?

A.    ip access-list extended ACL_OUTBOUND
permit ip 10.1.1.0 0.0.0.255 any
interface Ethernet1
ip access-group ACL_OUTBOUND out
B.    interface Ethernet1
ip nat outside
C.    interface Ethernet0
ip nat inside
D.    ip route 0.0.0.0 0.0.0.0 198.51.100.1

Answer: D

QUESTION 46
It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)

A.    REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
B.    REP converges faster than Spanning Tree, allowing for greater network availability.
C.    REP supports Industrial Ethernet protocols better because it moves the packets faster.
D.    Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
E.    Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.

Answer: BD

QUESTION 47
Which scenario represents the correct configuration to support the SSIDs of this autonomous access point?

A.    Missing
B.    Missing
C.    Missing
D.    Missing

Answer: D

QUESTION 48
In which two ways could you minimize the impact of monitoring an industrial network? (Choose two.)

A.    Send random messages to a device and see what the response is.
B.    Do frequent ping sweeps to industrial devices to check for their proper operations.
C.    Make a copy of all the network traffic and analyze it offline.
D.    Use an industrial-network-grade IDS-IPS system.

Answer: CD

QUESTION 49
Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)?

A.    Can be used to override both static and dynamically (DHCP/BOOTP) assigned IP addresses
B.    Cannot be used to reset a device to factory defaults
C.    Is only supported in Conformance Class B and C devices
D.    Uses the ProfiNET-IRT communication class

Answer: A

QUESTION 50
When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?

A.    Use of shielded Patch Cables, Bonded on one end only.
B.    Use of unshielded Patch Cables.
C.    Broken seal on bulkhead connector.
D.    Oxidation on Shielded RJ45 Patch Plug

Answer: D

We give you the proper and complete training with free 200-601 Lead2pass updates. Our braindumps will defiantly make you perfect to that level you can easily pass the exam in first attempt.

200-601 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDSzdjNVg5Qk83Y2s

2016 Cisco 200-601 exam dumps (All 70 Q&As) from Lead2pass:

http://www.lead2pass.com/200-601.html [100% Exam Pass Guaranteed]

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back